Funssor 1set*kossel k800 mini 3D printer magnetic effector carriage180mm carbon tube Diagonal push rods kit

Funssor 1set*kossel k800 mini 3D printer magnetic effector carriage180mm carbon tube Diagonal push rods kit
  • Продавец
  • Список ценUS $37.99piece
  • Продажная ценаUS $37.99piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,3 (781)

Oписание продукта






Product List:

Rod Kit:

- Blue PDR Rods with different sizes (B4,B5,B7)

-Black PDR Rods with different sizes (C1-C6)

-1PC Blue Wiper

-2PCS  Siderosphere

-2PCS S Hook

Dent Kit:
-1PC Black glue gun

-1PC  Dent lifter Red

-2PCS Blue tabs (5 different sizes,10PCS)

-1PC Red tabs(10 different sizes)

-1PC Black tabs(9 different sizes,9PCS)
-1PC Line board
-1PC Puller Bridge Kit Golden
-1PC Blue Tap Down with 2 heads
-1PC Yellow Plastic shovel

-4PCS Black glue sticks
-4PCS Yellow glue sticks

-1PC Hammer
-1PC Blue Bag
-1PC Red Plastic shovel
-1PC Red Wedge

-1PC Red T puller

-1PC Slide Hammer
-1PC Repair Hammer
Size for manual measurement, there may be a 0 to 2 cm error, belongs to the normal phenomenon.

And due to the difference between different monitors, the picture may not reflect the actual color of the item.


How to use this paintless dent repair kits?

1.Use a line board to find the dent,clean the dent with a clean cloth;
2.Mount the glue stick into the glue gun,pull the trigger to let the glue stick enter into the glue gun, connect the power source and preheat for 5 minutes;
3.Pull the glue gun\'s trigger to let the hot melt glue apply evenly onto the gule tabs;
4.Fast place the gule tabs with hot melt glue at the center of dent, press lightly until the glue cures and adheres (Let the glue cool for about 8 minutes. The cooling time should be less than 10 minutes and should be shorter slightly in winter);
5. Use the dent lifter/silde hammer/T-handle dent puller to pull up the dent;
6. Check with a line board. If dent still exists, knock it slightly with a Rubber Hammer and tap down;
7. Clean the repaired place with a clean wet cloth.

Please unplug the power supply after stop using the hot melt glue gun.
Please don\'t pull the glue stick out of the the hot melt glue gun if the hot melt glue stick have not been used up.


PDR tool (4)
how to repair
How to use the dent lifter?
PDR Dent Repair tool set (2)


How to use the pulling bridge?

Pulling Bridge Dent Removal Hand Tool Set (1)

How to use the slide hammer?



How to use the rod hooks?





We accept Alipay, West Union, TT. All major credit cards are accepted through secure payment processor ESCROW.
Payment must be made within 15 days of order.
If you can\'t checkout immediately after auction close, please wait for a few minutes and retry Payments must be completed within 15 days.


Item are shipped within 3 business days once full payment is settled. If you can\'t get your items in time, please contact to us first,

we will check and solve it for you soon. We will reply your mail within 24 hours normally. Sometimes have a little delay due to the

weekend or holiday. If you can\'t get our mail after 48 hours, please check your spam or contact to us with other mail address.


Furuix provide 18 months product Warranty. If item defective in 3 Month, We will offer replacement without any hesitation. If item

Defective after 3 Month, Buyers can still send it back, we will replace or repair the product. Buyers might need pays the shipping

fee for resend the replaced item.



All Furuix products are high quality ones. We never contact customer to revise the bad feedback, which we have the confidence to show the real feedback to our customer, so if you have any issue for your order, please contact us, we will provide the 100% satisfied solution for our customer. However if we noted any customer to give us bad feedback (fake feedback) in order to get the full refund,we will pull this customer to the black list and never deal with them in the future.